Service Hotline
+8613809882437
Products

Product Categories

T-8000C SD Card LED Controller

T-8000C SD Card LED Controller

Shenzhen Oxford Lighting Co.,Limited is one of the professional t-8000c sd card led controller manufacturers and suppliers in China, welcome to wholesale t-8000c sd card led controller made in China and check its price with our factory. 1. T-8000C System features 1、32—256 Gray level,Support...

Products Details

Shenzhen Oxford Lighting Co.,Limited is one of the professional t-8000c sd card led controller manufacturers and suppliers in China, welcome to wholesale t-8000c sd card led controller made in China and check its price with our factory.

1. T-8000C System features

1、32—256 Gray level,Support software Gamma correction。

2、Support the rules and special-shaped handle.

3、Eight--port output,every port can support 512-1024 pixels。

4、Offline (SD Card) control ,can be multiple controllers used in combination, play back content stored in the SD card.

5、Compatible with single and dual IC, if you control a single line IC LED lights, without being connected to the CLK line.

6、New T-8000C have a screen, The controller can be encrypted to limit the times of use.

NOTE:1. When T-8000C controller control less than 512 lamps the frame rate can reach 30fps. When T-1000 controls more than 512 lamps and less than 1024 lamps the frame rate will slow down automatically.

2. In the 2012 production version of the T-8000C to add a Chinese flag on the surface, you must use the new software.   

2. Appearance picture 

3. The meaning of flag

Button

Meaning

SET

Save your adjust

MODE

Switch effect file

SPEED+

Turn up speed

Press the speed adjustment button the file will in turn play.

SPEED-

Turn down


DC5V

Power input

POWER

Power light

ERROR

Error indicator

SD/SD CARD

SD card slot


CLK

Clock line

DAT

Data line

GND

Ground wire

NOTE:For the TTL(SPI) signal, the controller signal ground must connect to the LED ground wire directly.

4. Mode of connection

NOTE:

1.If the distance between controller and lamps more than 50m we suggest using differential signal transmission control or Photoelectric isolated signal transmission control,please read the manual carefully. Signal lines must be a cable,the best is Super five kinds of cable.

5. Specific parameters:

Memory card:

type:SD card(suggest using high-speed SD card)

Capacity:128MB—2GB

Format:FAT

Store file Format:*.led

Physical parameters:        

Working temperature :-30℃—85℃

Working voltage:DC5V

Working power:3W

Size:L200mm×W170mm×H50mm

Weight:1.5KG

Signal port:3pin connect port

NOTE:

Before copy files to SD card ,The SD card must be formatted as FAT format.

The SD card in controller can not be hot-swappable, plug the SD card every time, you must first disconnect the power supply

6.T-8000C GPS Wireless synchronization schemePicture

GPS wireless synchronized receiver

Production characteristic

1. Solve the problem that can't install the cable between the buildings and the buildings so caused by the controller and the controller cannot work synchronously.

Product standard

size:L163mm * W93mm * H30mm         

weight:0.3KG

working voltage:DC5V                       

Power:2W

Working temperature:-20℃--80℃                

The wiring diagram

7.Trouble shooting:

Question 1:After power, the T-8000C ERROR indicator has been flashing without display output

answer:The ERROR indicator has been flashing means the controller did not read the card correctly, possible problems:

①SD card is empty, with no effect file.

②The effect file in the SD card and the controller model are not match, please choose correct controller model in LedEdit and then re-create the effect file *led.

③SD card did not format to FAT before copy effect files.

④Please check the supply power voltage, the controller can be individually powered to exclude power reasons

⑤Changing the SD card and then test to exclude the possibility of a bad SD card

Question 2: The controller is powered on, the indicator is normal, but the lamps have no effect change

Answer: The reasons for this are as follows: 

① Check if the lamp′s signal line and the controller connected correctly

②If the TTL signal is received, the lamp and the controller must be common ground, that means connect the lamp′s and the controller′s ground wire together

③Check if the model chose during making display files on the SD card match the chips used in the lighting

Question 3:Controller and light connected, after. Lamps flicker. Controller indicator to normal.

Answer:①The ground wire is not connected between the controller and lighting.

②The file in SD card is bad, Chip model does not match with the actual.

③Insufficient power supply.

Question 4:The SD card can not be formatted.

Answer:①First make sure the SD card on the side of the protection switch is already open.

②SD card reader is broken

③Do all of this can’t deal with the question. Change the SD card tests again.



Hot Tags: T-8000C SD card LED controller manufacturers China, suppliers China, made in China, factory, wholesale, price
Related Products
Feedback
Feedback
Send
Contact Us
Address: East Ring Road ,Huangpu Community, Shajing Town,Bao'an District,Shenzhen,China
Tel: +8613809882437
Fax: +8613809882437
E-mail: oxford.adsleds@yahoo.com
No.1109 of the first Building, No.46 Plant, East Ring Road, Huangpu Community, Shajing Town, Bao'an District,Shenzhen,Guangdong,(518125),China