Service Hotline
+8613809882437
Products

Product Categories

Programmable Led Controller With 8G SD Card

Programmable Led Controller With 8G SD Card

1、32 to 65536 degree Gray control, Gamma correction procession handle. 2、Support various point, line light source, and all kinds of rules and specific shaped handle. 3、The controller has eight ports output, each port can support up to 512/1024 lights(DMX lights can support up to 512 pixels). 4、The playback content stored in SD card, the SD card can store up to 32 files, SD cared capacity supports 128MB-32GB.

Products Details

K-8000C Using Manual

4M4BFRS$WVDNPS_S@PX@XTL_副本_副本

一、K-8000C system features:

    1、32 to 65536 degree Gray control, Gamma correction procession handle.

2、Support various point, line light source, and all kinds of rules and specific shaped handle.

3、The controller has eight ports output, each port can support up to 512/1024 lights(DMX lights can support up to 512 pixels).

4、The playback content stored in SD card, the SD card can store up to 32 files, SD cared capacity supports 128MB-32GB.

5、The controller can single set use,also multiple controllers cascade, cascade optical isolation mode: interference, better stability, cascade distance between two controllers can reach up to 150 meters, need to use 0.5M² pure copper power cord.

6、The controller support chip can lock the support IC in software, or not lock the support IC in the software, select the support IC through the controller CHIP button, this scheme is more flexible and convenient.

7、For the DMX lighting IC, the controller comes with write address function; In addition,  with use of our 2016 LedEdit-K V3.26 or later edition can make one key write address function setting.

8、Support load lamp is 4 channels (RGBW) pixels, or split into single channel point pixels.

9、Enhanced 485 TTL and 485 differential (DMX) signal output.  

10、The controller comes with the test effects were as follows: 1 red, green, blue and black jump; 2 red, green, blue and black gradient; 3 red, green, blue and goes.

Notes: 1, The controller load lamps 512 points pixel, speed can reach up to 30 frames / sec, 768 point pixel speed can reach up to 25 frames / sec, 1024 point pixel speed is about 22 frames / sec (the above parameter is an example of 1903 agreement IC, different IC have difference)

2、 International standard DMX512 (1990 agreement) maximum support 512 pixels. When the load is international standard 170  pixels, the speed can reach up to 30 frames / sec, 340 pixels speed is about 20 frames / sec, when 512 pixels speed is about 12 frames / sec.

3、Timing (holidays) Play Global Wireless GPS synchronization, control station channel distributor, please contact the salesman or technical support staff for more information.

二、Support chips(PC Software Select K-8000-RGB)

00: UCS1903,1909,1912,2903,2904,2909,2912;TM1803,1804,1809,1812;

SM16703,16709,16712;WS2811;INK1003;LX3203,1603,1103;GS8205,

8206;SK6812(Support up to 1024*8=8192 pixels)  

01:SM16716,16726(Support up to 1024*8=8192 pixels)  

02:P9813(Support up to 1024*8=8192 pixels)  

03:LPD6803(Support up to 1024*8=8192 pixels)   

04:LX1003,1203(Support up to 1024*8=8192 pixels)  

05:WS2801(Support up to 1024*8=8192 pixels)                

06:LPD1886(Support up to 1024*8=8192 pixels)  

07:TM1913(Support up to 1024*8=8192 pixels)                 

08:TM1914(Support up to 1024*8=8192 pixels)  

09:P9883,P9823(Support up to 1024*8=8192 pixels)         

10:DMX(Support up to 512*8=4096 pixels, suggest to support ≤320*8=2560 pixels)

11:DMX 500K(Support up to 512*8=4096 pixels, suggest to support ≤320*8=2560 pixels)

12:DMX 250K-CZF (Support up to 512*8=4096 pixels, suggest to support ≤320*8=2560 pixels)

13:DMX 250K-CZF (Support up to 512*8=4096 pixels, suggest to support ≤320*8=2560 pixels)

NOTES: 1.If support RGBW four channels’ lights should select K-8000-RGBW.

      2.If support single channel light should choose K-8000-W, at this time, one channel means one pixel, the software effect make as white lighting.


 

三、Appearance Picture:

A}B%RB2S[8)CBN1%)`EB]]C


四、
Screen print meaning 

     Button meaning:

Button

Meaning

SHIP

Select chip model

Press CHIP and   then MODE button, can enter write code mode, 61 means UCS512-A/B coding; 62   means WS2821 coding; 63 means SM512 coding, 64   means UCS512-C coding

MODE

Switch files

SPEED+

Speed up

Press SPEED+   and SPEED- the same time, would enter effect files looping mode

SPEED-

Speed down

 

Power supply

DC5V   input/DC12-24 input

POWER

Power   indicator

SYNC

Cascade   indicator

STATUS

Status   indicator

SD CARD

SD card   slot

 

Signal output(TTL/245 signal):

GND

GND(negative   electrode)

DAT

Data

CLK

Clock


 

Signal output(DMX512 signal):

GND

GND(negative   electrode)

A/DAT+

Signal +

B/DAT-

Signal -

ADDR

Coding line


The corresponding frame rate of speed level

Speed Level

 Frame Rate/Sec

Speed Level

Frame Rate/Sec

1

4 frame

9

14 frame

2

5 frame

10

16 frame

3

6 frame

11

18 frame

4

7 frame

12

20 frame

5

8 frame

13

23 frame

6

9 frame

14

25 frame

7

10 frame

15

27 frame

8

12 frame

16

30 frame

 

 

五、Conventional IC lamps wiring

IR@UGN3TTURO$9X[36AD{@X


六、Controller support DMX lights coding and wiring method:

Two signal wiring diagram:

XEJ{B%HUNE]NQ7$Y@AKZ525

 

Single signal wiring diagram:

%2[X$N}Q%HDGWLGPB]@EQ0P

 

1.Like the above diagram, wired the line and start the controller, press “CHIP”and “MODE” at the same time switch to coding mode, adjust to Chip: 61 that is UCS512A or B coding mode, as below:


NOTE:61 means UCS512A or B coding mode; 62 means WS2821 coding mode; 63 means SM DMX512AP; 64 means UCS512-C;Ch.:03 means the coding channel is 3 channels

 

    2. After selection, press “MODE” to code, then the screen would display A A A. Until finished coding, it would show Writing OK, Like below:


3.After finished address code, press “CHIP” first and at the same time press “MODE”button, switch to playback mode, switch the chip to Chip: 10, this is the DMX512 standard agreement 250K playback mode. At this time, press MODE button and SPEED button can separately switch playback mode and adjust speed, as below: 

 


Special RemarksDerived program after set one-key coding in the software, long press MODE for 5 seconds can write code to the lights directly, this function is very convenient and practical. Welcome to consult our engineer or salesman to learn the detailed operation method.

 

 

七、Encryption Glossary Explanation

Password is OK

Password   normal!

Num

The   remaining boot times

Password exist

Password   has existed

Can't repeated

Can’t   repeat set password

Set Password OK

Password   set successfully

Clear Pwd OK

Clear   password successfully

Pwd not right

Password   not correct

No Password

Password   don’t exist

Has expired! Contact factory

Password   expired, please contact the factory!

八、Specific parameter:

   Memory card:

         Type: SD card

          Capacity:  128MB—32GB

          Format:FAT or FAT32 format

          Storage files: *.led

    Physical parameter:

         Working temperature:-20℃—85℃

          Working power:DC 5V or DC 12-24V input

          Power consumption: 5W

      Weight: 0.8Kg

      Size:


九、NOTES

     1、To copy files to SD card, you must format the SD card first, pay attention to is that each copy must be formatted first.

     2、SD card must be formatted as FAT form or FAT32 form.

3、The SD card can not be hot-swappable, plug the SD card each time, you must first disconnect the power supply controller.


十、How to handle the common problems:

Problem 1: After powered on, the controller screen display SD Error, and no effect output.

Answer: The screen display SD Error means the controller did not read the SD card correctly, the exist problems as below:

    ①SD card is empty, has no effect files.

②The effect files *.led in SD card and the controller model is mismatch, please select correct controller model, chip model in the latest edition 2016LedEdit, and remake effect files *.led.

③Change SD card and then retesting, rule out the possibility of SD card is broken.

Problem 2: After powered on, the indicator is normal, but the lamps has no effects change.

     Answer: It has the following reasons for this problems:

         ①Please check if the signal line of the lamps and the controller connected correctly.

         ②Conventional lamps signal divided into input and output, please confirm whether the controller connected the first lamp’s  signal input.      

 

Problem 3: After connect the lamps and the controller, the lamps is strobe and has effect change, at the same time the controlled indicator shows normal.

     Answer:

①The ground line of the controller and the lamps are not connected.

         ② The effects in SD are not correct. The IC of the lamps when making effect is not corresponding with the IC of the actual lamps.

         ③If did not lock the chip, when making effects in the software, need to press the controller chip to the light’s corresponding chip, about press to which number, please refer to the sticker IC order on the controller.

         ④The power supply voltage of the lamps is insufficient.

 

Problem 4 SD card can not be formatted.

Answer:①Firstly, make sure if the protection switch on the side of SD card is unlocking. The unlocking direction is the gold needle side of SD card.

②The protection has designed as required, but can not formatted, if this condition appears, it always because the SD card reader is broken, please change the SD card reader(had better use good quality card reader, SSK card reader is suggested).

③If the above operations can not solve the formatting problems, please change the SD card and retest.

 

 


Hot Tags: programmable led controller with 8g sd card manufacturers China, suppliers China, made in China, factory, wholesale, price
Related Products
Feedback
Feedback
Send
Contact Us
Address: East Ring Road ,Huangpu Community, Shajing Town,Bao'an District,Shenzhen,China
Tel: +8613809882437
Fax: +8613809882437
E-mail: oxford.adsleds@yahoo.com
No.1109 of the first Building, No.46 Plant, East Ring Road, Huangpu Community, Shajing Town, Bao'an District,Shenzhen,Guangdong,(518125),China